Download Article

Download Article

PUR has multiple products available for filtering water, but the filters become less effective over fourth dimension as they fill with contaminants. How you supercede the filter depends on which system you lot're using. If you take a plastic pitcher or dispenser you go along in the fridge, soak the new filter earlier screwing it in. For filtration systems that attach to your sink faucet, just remove the old filter so you can put the new one in its identify. When you're finished, you'll take clean water to drink for another few months!

  1. 1

    Soak the replacement filter in cold h2o for 15 minutes. Place the new filter in a clean container that's deep plenty so yous can fully submerge it. Fill the container with cold water and leave it solitary for at least 15 minutes. During this time, any backlog carbon from the filter will lift out and split so it doesn't get in your drinking water.[1]

    • Soaking the filter likewise ensures that water flows evenly when you apply it.
    • Don't use h2o warmer than 86 °F (xxx °C) since it could damage the filter.

    Alarm: Avoid using third-party filters with your PUR pitcher or dispenser since they may not fit likewise or take been tested as efficiently.

  2. 2

    Twist the old filter counterclockwise to remove information technology. Take the lid off of the pitcher or dispenser and set it aside. Then, elevator up the pour tray, which is the blueish plastic reservoir on elevation, and take it out. Grab the cylindrical filter from the bottom and rotate information technology counterclockwise so it unhooks from the filter. Pull the erstwhile filter out through the tiptop of the pour tray and throw in the garbage.[2]

    • Wait until the cascade tray is empty to change your filter, or else it may be difficult to remove or you may spill.

    Advertising

  3. iii

    Rinse the new filter under your faucet for 10 seconds. Take the filter out of the container when information technology's finished soaking and concord it underneath your faucet. Turn on cold h2o and rotate the filter so you can rinse it off completely. Afterward 10 seconds, plow off the water and shake out any excess that'southward still in the filter.[three]

    • Don't use hot h2o to rinse the filter off, or else you may impairment it.

  4. iv

    Spiral the filter clockwise into the pour tray to secure it. Slide the long, cylindrical part of the filter through the hole in the middle of the cascade tray and button information technology down as far as information technology goes. Hold the filter by the bottom and rotate it clockwise until y'all hear information technology click into place. Try borer on the end of the filter to make sure it doesn't pop out from the pour tray. Place the pour tray back into the pitcher or dispenser before replacing the lid.[4]

    • If the filter does popular out of the pour tray, then you didn't properly secure it. Reinsert it and attempt turning it clockwise again.
    • PUR filters for pitchers and dispensers usually work for 40 gallons (150 L), or approximately two months.

  5. 5

    Hold the Reset button down for 5 seconds if your bullpen or dispenser has one. Some newer PUR pitchers and dispensers have sensors that detect when you lot need to replace the filter. Right after y'all supplant the filter, printing the Reset button on the lid and continue it held down for 5 seconds. A green light will blink on the chapeau once the sensor resets.[v]

    • Older pitchers or dispensers may not take an electronic display.

    Advertisement

  1. 1

    Unscrew the filtration organization from your faucet. Support the weight of the filtration organization with your nondominant hand so information technology doesn't autumn and break. Rotate the plastic locking nut holding the filtration organisation to the faucet counterclockwise to loosen it. Once you lot unscrew the system completely, carefully elevator it away from the faucet and set it down on a countertop or towel.[six]

    • H2o may spill out from the faucet when you unscrew the filtration system.
    • Some models of PUR filtration systems may snap onto the faucet. If it doesn't unscrew, try pulling it direct down from the faucet.

  2. 2

    Twist open up the elevation cover of the system to remove the old filter. Hold the filtration system then the rounded end of the large cylinder points up. Unscrew the top from the cylinder by rotating it counterclockwise, and set the cover aside. Pull the old filter direct out from the system and throw it away in your trash.[7]

    • The top comprehend is always on the reverse end of the spout that dispenses water.

  3. 3

    Set the new filter inside of the system and screw on the cover. Make certain the narrower cease of the filter is on the lesser and the logo is right-side up. Place the filter into the filtration system so it has a loose fit. Set the tiptop embrace back over the filter and spiral information technology into place to secure information technology.[8]

  4. four

    Reattach the filtration system to your faucet. Hold the filtration organization against the bottom of the faucet and then the threadings are perfectly horizontal, or else they won't form a tight seal. Rotate the locking nut clockwise onto the faucet and keep tightening it until it's hand-tight. Plough on the h2o and make sure information technology doesn't drip or leak at the seam.[9]

    • If your filtration system doesn't screw on, line it up with the faucet and apply business firm pressure to snap it on.

  5. 5

    Run cold water through the filtration arrangement for 5 minutes. Plow the handle on the correct side of the filtration system to divert the water through the filter. Let the h2o to run through the filter for 5 minutes to go rid of any residue within so information technology works more than efficiently. After that, you tin use the filter immediately after turning it on.[x]

    • PUR faucet filters work for 100 gallons (380 50) of water, or about 3 months of utilise.
    • Don't run h2o over 100 °F (38 °C) through the filter since you lot could impairment it.

    Warning: The water may sputter or await cloudy when you first utilize the new filter, just it will become amend as you run water through it.

    Advertisement

Ask a Question

200 characters left

Include your email accost to get a bulletin when this question is answered.

Submit

Ad

  • Many PUR filtration systems have electronic lights that detect when you need to change your filter. If you see a greenish light wink, you don't need to change your filter. If information technology blinks yellow or ruddy, then y'all need to supersede the filter before long.[xi]

Thanks for submitting a tip for review!

Advertisement

  • Don't use h2o that's above 82 °F (28 °C) in a pitcher or over 100 °F (38 °C) through a faucet since information technology can damage the filter.[12]

  • Simply use the filter with h2o that's already safety to drink since it will not remove bacteria or infection.[13]

Advertisement

References

Near This Commodity

Cheers to all authors for creating a folio that has been read twoscore,683 times.

Did this article help you?